Contact Us |
Drawing and Part Number Lookup
920-569-0140
Foam Tool Organizer for
72 Husky Impact Sockets and 9 Drive Tools
Overview
72 Husky Impact Sockets and 9 Drive Tools
Fits (72) Husky impact sockets and (9) drive tools.
Accommodates most of the impact sockets and drive tools from the Husky 1025-pc set H1025MTS.
Caution: Recommended for minimum of 3 inches of dawer height.
Drawer Size
15 X 21-5/8 inches
$63.70
Details
- Drawer size: 15 X 21-5/8 inches (inside width by inside depth)
- Standard colors: black/red, blue/yellow, black/blue
- Made from closed-cell polyethylene tool foam.
- Precision CNC-cut to fit 81 Husky impact tools:
Sockets:
(9) 3/8-drive 6-point inch sizes from 1/4 to 3/4
(9) 3/8-drive 6-point inch deep sizes from 1/4 to 3/4
(9) 3/8-drive 6-point metric sizes from 10 to 15 and 17 to 19 mm
(9) 3/8-drive 6-point metric deep sizes from 10 to 15 and 17 to 19 mm
(11) 1/2-drive 6-point inch sizes from 7/16 to 1-1/16
(7) 1/2-drive hex bit sizes from 1/4 to 3/4
(11) 1/2-drive 6-point metric sizes from 13 to 19 and 21, 22, 24, 27 mm
(7) 1/2-drive hex bit sizes from 9 to 15 mm
Drive Accessories:
3/8 X 3 extension (H2DIMPEXT3)
3/8 X 6 extension (H2DIMPEXT6)
3/8-drive swivel
3/8 to 1/2-drive adapter (HIMPADP3DF2DM)
1/2 X 3 extension
1/2 X 6 extension
1/2 X 10 extension
1/2-drive swivel (H2DIMPUNIV)
1/2 to 3/8-drive adapter (HIMPADP2DF3DM)
Free shipping on all orders within the contiguous 48 US states.
Made in the USA!
note: tools are not included
Tool Requirements
This organizer was designed to fit most of the impact sockets and drive tools from the Husky 1025-pc set H1025MTS. The 1/2-drive deep sockets are excluded to allow it to fit in a 3-inch tall drawer.
Possible Modifications
Minimum trimmable size:
14-1/4 X 19-5/8 inches
Note: Trimmed organizers are not returnable.
Contact customer service to order this organizer cut on a larger sheet or trimmed to a special size.
Colors by special request:
black/yellow, black/green, black/gray
Contact customer service to order this organizer in a special color.
Drawing
Please verify this organizer fits your tools before placing an order.
- Download the drawing: www.FoamFitTools.com/product/F-05189-T.pdf
- Print the pages of the drawing full size or 100% (not fit).
- Check that the printout is full size by measuring the border with a ruler.
- Assemble the pages and place the printed drawing in your toolbox drawer.
- Place the tools over the printed outlines. Visually check that each tool fits within its outline.
Additional Information
Each FoamFit insert is designed for shadowing a specific set of tools. These organizers are made from high-quality tool foam with precision-cut pockets.
The pockets are cut up to 1/2 inch deep in 3/4 inch thick tool foam, or up to 1 inch deep in 1-1/4 inch thick tool foam. Most inserts require less than 2 inches of height to fit in a 2-inch drawer (unless otherwise noted).
Our tool foam is two layers of closed-cell polyethylene foam. The contrasting top layer is thermally bonded to the bottom layer for maximum durability. Three color combinations are available: black with red, blue with yellow, and black with blue. The foam is resistant to most oils and fuels.
