Fits (14) open-end wrenches, (10) flare-nut wrenches, (20) crow foot wrenches, and (16) ignition wrenches.
Accommodates the wrenches from the Craftsman 60-pc set CMMT87903.
Recommended for 2-9/16 min drawer height.
Drawer Size
22-1/4 X 16-1/4 inches
$70.90
larger image
note: tools are not included
Precision CNC-cut to fit 60 Craftsman wrenches:
crow foot:
3/8-drive, 3/8
3/8-drive, 7/16
3/8-drive, 1/2
3/8-drive, 9/16
3/8-drive, 5/8
3/8-drive, 11/16
3/8-drive, 3/4
3/8-drive, 13/16
3/8-drive, 7/8
3/8-drive, 1
double open-end
1/4 X 5/16 (CMMT87063)
5/16 X 3/8 (CMMT87064)
7/16 X 1/2 (CMMT87065)
9/16 X 5/8 (CMMT87066)
11/16 X 3/4 (CMMT87067)
25/32 X 13/16 (CMMT87068)
15/16 X 7/8 (CMMT87069)
flare-nut:
1/4 X 5/16 (CMMT42090)
3/8 X 7/16 (CMMT42091)
1/2 X 9/16 (CMMT42092)
5/8 X 11/16 (CMMT42093)
3/4 X 7/8 (CMMT42094)
ingnition (mini angle):
7/32
15/64
1/4
9/32
5/16
11/32
3/8
7/16
crow foot wrenches:
3/8-drive, 10 mm
3/8-drive, 11 mm
3/8-drive, 12 mm
3/8-drive, 13 mm
3/8-drive, 14 mm
3/8-drive, 15 mm
3/8-drive, 16 mm
3/8-drive, 17 mm
3/8-drive, 18 mm
3/8-drive, 19 mm
double open-end:
6 X 7 (CMMT87070)
8 X 9 (CMMT87071)
10 X 11 (CMMT87072)
12 X 13 (CMMT87073)
14 X 15 (CMMT87074)
16 X 17 (CMMT87075)
18 X 19 (CMMT87076)
flare-nut:
9 X 11 (CMMT42095)
10 X 12 (CMMT42096)
13 X 14 (CMMT42097)
15 X 17 (CMMT42098)
16 X 18 (CMMT42099)
ingnition (mini angle):
5 mm
5.5 mm
6 mm
7 mm
8 mm
9 mm
10 mm
11 mm
This tool organizer was designed to fit the wrenches from the Craftsman 60-pc specialty wrench master set CMMT87903. The full-polish, open-end and flare-nut wrenches have a pattern of diagonal lines stamped before and after the word "Craftsman". The small "ignition" wrenches are configured like angle wrenches, with open ends at 15 and 60 degrees.
Printing the drawing at 100% scale can be an easy way to check if your tools will fit. Our drawings have multiple pages which can be printed on letter-size paper. Always change the printer setting from "fit" to 100%. If the border prints slightly too small, it is often due to this setting.
22-1/4 X 16-1/4 inches (inside width by inside depth)
Recommended for a drawer with at least 2-9/16 inches of vertical clearance.
It is possible to trim the margins to fit a smaller drawer. Trimmed tool organizers are not returnable. The minimum recommended size is:
21-3/4 X 15-5/16 inches
Contact customer service to order this organizer cut on a larger sheet or trimmed to a special size.
We make these colors in smaller batches, but they are often in stock. Contact customer service to order.
Each FoamFit insert is designed for shadowing a specific brand and set of tools. These organizers are made from high-quality tool foam with pockets precision-cut on our CNC routers.
The pockets are cut up to 1/2 inch deep in 3/4 inch thick tool foam, or up to 1 inch deep in 1-1/4 inch thick tool foam. Most inserts require less than 2 inches of height to fit in a 2-inch drawer (unless otherwise noted).
Our tool foam is two layers of closed-cell polyethylene foam. The contrasting top layer is thermally bonded to the bottom layer for maximum durability. The foam is resistant to most oils and fuels.