Foam Tool Organizer for
22 Hex Screwdrivers, High-Torque Handle


22 Hex Screwdrivers, High-Torque Handle

Fits the 22-pc high-torque hex driver set DHX91301.

Fits (10) inch hex and (12) metric hex sizes.

Only fits Tekton high-torque screwdrivers. Does not fit the red, hard-handle screwdrivers.


Drawer Size
23-3/4 X 17-3/4 inches


Foam Organizer for 22 Hex Screwdrivers, High-Torque Handle

larger image

Foam Organizer for 22 Hex Screwdrivers, High-Torque Handle

larger image

note: tools are not included

Tool List

Precision CNC-cut to fit 22 Tekton hex drivers:

inch sizes:
5/64 (Tekton DHX11079)
3/32 (Tekton DHX11094)
7/64 (Tekton DHX11110)
1/8 (Tekton DHX11125)
9/64 (Tekton DHX11141)
5/32 (Tekton DHX11157)
3/16 (Tekton DHX11188)
7/32 (Tekton DHX11219)
1/4 (Tekton DHX11250)
5/16 (Tekton DHX11313)

metric sizes:
1.5mm (Tekton DHX21015)
2mm (Tekton DHX21020)
2.5mm (Tekton DHX21025)
3mm (Tekton DHX21030)
3.5mm (Tekton DHX21035)
4mm (Tekton DHX21040)
4.5mm (Tekton DHX21045)
5mm (Tekton DHX21050)
5.5mm (Tekton DHX21055)
6mm (Tekton DHX21060)
7mm (Tekton DHX21070)
8mm (Tekton DHX21080)

Tool Notes

This organizer was designed to fit the 22 Tekton High-Torque hex screwdrivers from set DHX91301. It also fits the hex screwdrivers included in 58-pc set DRV41241. Sets DHX91101 and DHX91206 could be combined to fill this organizer along with a few other sets that contain the same sizes.


Drawing F-05464-R.pdf

Printing the drawing at 100% scale can be an easy way to check if your tools will fit. Our drawings have multiple pages which can be printed on letter-size paper. Always change the printer setting from "fit" to 100%. If the border prints slightly too small, it is often due to this setting.

Drawer Size

23-3/4 X 17-3/4 inches (inside width by inside depth)

Drawer Height

Works in most drawers, needing no more than 2 inches of vertical clearance.

Minimum Trimmable Size

It is possible to trim the margins to fit a smaller drawer. Trimmed tool organizers are not returnable. The minimum recommended size is:

21-3/4 X 15-15/16 inches

Contact customer service to order this organizer cut on a larger sheet or trimmed to a special size.

Features and Benefits

Standard Colors

black over red color combination blue over yellow color combination black over blue color combination

Special Colors

We make these colors in smaller batches, but they are often in stock. Contact customer service to order.

black over yellow color combination black over green color combination black over gray color combination

Additional Information

Each FoamFit insert is designed for shadowing a specific brand and set of tools. These organizers are made from high-quality tool foam with pockets precision-cut on our CNC routers.

The pockets are cut up to 1/2 inch deep in 3/4 inch thick tool foam, or up to 1 inch deep in 1-1/4 inch thick tool foam. Most inserts require less than 2 inches of height to fit in a 2-inch drawer (unless otherwise noted).

Our tool foam is two layers of closed-cell polyethylene foam. The contrasting top layer is thermally bonded to the bottom layer for maximum durability. The foam is resistant to most oils and fuels.

Free Shipping!

For orders within the contiguous 48 US states.

US flag

Made in the USA!