Fits the combination and angle head wrenches from the aviation technician bundle.
Fits (15) combination wrenches, (11) stubby wrenches, and (11) angle head open end wrenches.
Drawer Size
37-1/8 X 19-3/8 inches
$106.10
larger image
note: tools are not included
Precision CNC-cut to fit 37 Tekton wrenches:
combination:
1/4 (Tekton 18251)
9/32 (Tekton 18252)
5/16 (Tekton 18253)
11/32 (Tekton 18254, only fits 6-1/8 inch long version)
3/8 (Tekton 18255, only fits 6-5/16 inch long version)
7/16 (Tekton 18256)
1/2 (Tekton 18257)
9/16 (Tekton 18258)
5/8 (Tekton 18259)
11/16 (Tekton 18261)
3/4 (Tekton 18262)
13/16 (Tekton 18263)
7/8 (Tekton 18264)
15/16 (Tekton 18265)
1 (Tekton 18266)
stubby:
1/4 (Tekton 18041)
9/32 (Tekton 18042)
5/16 (Tekton 18043)
11/32 (Tekton 18044)
3/8 (Tekton 18045)
7/16 (Tekton 18046)
1/2 (Tekton 18047)
9/16 (Tekton 18048)
5/8 (Tekton 18049)
11/16 (Tekton 18051)
3/4 (Tekton 18052)
angle head:
3/8 (Tekton WAE83010)
7/16 (Tekton WAE83011)
1/2 (Tekton WAE83013)
9/16 (Tekton WAE83014)
5/8 (Tekton WAE83016)
11/16 (Tekton WAE83017)
3/4 (Tekton WAE83019)
13/16 (Tekton WAE83021)
7/8 (Tekton WAE83022)
15/16 (Tekton WAE83024)
1 (Tekton WAE83025)
This tool organizer was designed to fit the combination, stubby, and angle-head wrenches from verison 1 or 2 of the Tekton Aviation Technician Bundle BDL99914. It has been sized for a US General 42-inch Series 3 roll cabinet drawer, but other drawer sizes are available by request. Tekton occasionally changes which tool sets are included in their bundles, so we recommend checking on the tools before ordering. This organizer fits wrench sets 18772, WCB94401, and WAE91204 (WCB90106, WCB90401, and WAE91002 would also work).
Printing the drawing at 100% scale can be an easy way to check if your tools will fit. Our drawings have multiple pages which can be printed on letter-size paper. Always change the printer setting from "fit" to 100%. If the border prints slightly too small, it is often due to this setting.
37-1/8 X 19-3/8 inches (inside width by inside depth)
Works in most drawers, needing no more than 2 inches of vertical clearance.
It is possible to trim the margins to fit a smaller drawer. Trimmed tool organizers are not returnable. The minimum recommended size is:
35-5/8 X 16 inches
Contact customer service to order this organizer cut on a larger sheet or trimmed to a special size.
We make these colors in smaller batches, but they are often in stock. Contact customer service to order.
Each FoamFit insert is designed for shadowing a specific brand and set of tools. These organizers are made from high-quality tool foam with pockets precision-cut on our CNC routers.
The pockets are cut up to 1/2 inch deep in 3/4 inch thick tool foam, or up to 1 inch deep in 1-1/4 inch thick tool foam. Most inserts require less than 2 inches of height to fit in a 2-inch drawer (unless otherwise noted).
Our tool foam is two layers of closed-cell polyethylene foam. The contrasting top layer is thermally bonded to the bottom layer for maximum durability. The foam is resistant to most oils and fuels.