Fits the screwdrivers and hex keys from the aviation technician bundle.
Fits (8) slotted screwdrivers, (8) phillips screwdrivers, (13) hex keys, (5) picks and hooks, and (1) scratch awl.
Only fits Tekton screwdrivers with red handles.
Drawer Size
22-1/4 X 19-3/8 inches
$65.90
larger image
note: tools are not included
Precision CNC-cut to fit 35 Tekton tools:
slotted:
1/4 X 1-1/2 (Tekton DSE10250)
1/8 X 4 (Tekton DSE31125)
3/16 X 4 (Tekton DSE31188)
1/4 X 4 (Tekton DSE31250)
5/16 X 4 (Tekton DSE31313)
3/16 X 8 (Tekton DSE34188)
1/4 X 8 (Tekton DSE34250)
5/16 X 8 (Tekton DSE34313)
phillips:
#2 X 1-1/2 (Tekton DSP10102)
#0 X 4 (Tekton DSP31000)
#1 X 4 (Tekton DSP31001)
#2 X 4 (Tekton DSP31002)
#3 X 4 (Tekton DSP31003)
#1 X 8 (Tekton DSP34001)
#2 X 8 (Tekton DSP34002)
#3 X 8 (Tekton DSP34003)
pick set PNH90101:
straight 1/8 X 3 (Tekton PNH21101)
45-degree 1/8 X 3 (Tekton PNH21102)
90-degree 1/8 X 3 (Tekton PNH21103)
90-degree hook 1/8 X 3 (Tekton PNH21104)
130-degree hook 1/8 X 3 (Tekton PNH21105)
other:
(13) ball-end hex key sizes 0.050 to 3/8 (Tekton KLX91102)
scratch and punch awl (Tekton 65731)
This tool organizer was designed to fit the screwdrivers, hex keys, and picks from verison 1 or 2 of the Tekton Aviation Technician Bundle BDL99914. It has been sized for a US General 42-inch Series 3 roll cabinet drawer, but other sizes are available by request. We always recommend confirming tool availability before ordering. The pockets for the 1/8 and P0 screwdrivers fit the newer handle which is 3-9/16 inch long.
Printing the drawing at 100% scale can be an easy way to check if your tools will fit. Our drawings have multiple pages which can be printed on letter-size paper. Always change the printer setting from "fit" to 100%. If the border prints slightly too small, it is often due to this setting.
22-1/4 X 19-3/8 inches (inside width by inside depth)
Works in most drawers, needing no more than 2 inches of vertical clearance.
It is possible to trim the margins to fit a smaller drawer. Trimmed tool organizers are not returnable. The minimum recommended size is:
21-1/4 X 16-15/16 inches
Contact customer service to order this organizer cut on a larger sheet or trimmed to a special size.
We make these colors in smaller batches, but they are often in stock. Contact customer service to order.
Each FoamFit insert is designed for shadowing a specific brand and set of tools. These organizers are made from high-quality tool foam with pockets precision-cut on our CNC routers.
The pockets are cut up to 1/2 inch deep in 3/4 inch thick tool foam, or up to 1 inch deep in 1-1/4 inch thick tool foam. Most inserts require less than 2 inches of height to fit in a 2-inch drawer (unless otherwise noted).
Our tool foam is two layers of closed-cell polyethylene foam. The contrasting top layer is thermally bonded to the bottom layer for maximum durability. The foam is resistant to most oils and fuels.