Fits a 12-pc set plus a 6-pc torx set and stubby 3-in-1 screwdriver.
Fits (6) slotted, (6) Phillips, (6) torx, and (1) stubby 3-in-1 screwdriver.
Only fits the newer black and red handles with a through-hole for hanging or a tether. This version is made in Germany.
Does not fit the older high-torque style handles that were made in the USA.
Drawer Size
23-3/4 X 17-3/4 inches
$66.60
larger image
note: tools are not included
Precision CNC-cut to fit 19 Tekton screwdrivers:
Slotted
1/8 X 4 (Tekton DWS07308)
3/16 X 4 (Tekton DWS07312)
3/16 X 8 (Tekton DWS07412)
1/4 X 4 (Tekton DWS07316)
1/4 X 8 (Tekton DWS07416)
5/16 X 4 (Tekton DWS07320)
Phillips
P0 X 4 (Tekton DWP00300)
P1 X 4 (Tekton DWP00301)
P1 X 8 (Tekton DWP00401)
P2 X 4 (Tekton DWP00302)
P2 X 8 (Tekton DWP00402)
P3 X 4 (Tekton DWP00303)
Torx
T10 (Tekton DWT01310)
T15 (Tekton DWT01315)
T20 (Tekton DWT01320)
T25 (Tekton DWT01325)
T27 (Tekton DWT01327)
T30 (Tekton DWT01330)
other
stubby 3-in-1 (Tekton DMT17002 or similar)
This tool organizer was designed to fit 19 Tekton screwdrivers. We started with the 12-piece set DWZ90011 and added the 6-piece torx set DWT90001. We also included a spot for stubby 3-in-1 screwdriver DMT17002. These screwdrivers are mostly the new handle style with a tri-lobe shape and a tether hole. They were new at the end of 2025 and are made in Germany. There are several other stubby 3-in-1 screwdrivers that will fit like model DMT17001 and others with black handles.
This layout is similar to F-06553-R, but it has two fewer screwdrivers allowing it to be trimmed to fit smaller drawers. See the notes below for the minimum size, or download the drawing below.
Printing the drawing at 100% scale can be an easy way to check if your tools will fit. Our drawings have multiple pages which can be printed on letter-size paper. Always change the printer setting from "fit" to 100%. If the border prints slightly too small, it is often due to this setting.
23-3/4 X 17-3/4 inches (inside width by inside depth)
Works in most drawers, needing no more than 2 inches of vertical clearance.
It is possible to trim the margins to fit a smaller drawer. Trimmed tool organizers are not returnable. The minimum recommended size is:
21-3/4 X 16 inches
Contact customer service to order this organizer cut on a larger sheet or trimmed to a special size.
We make these colors in smaller batches, but they are often in stock. Contact customer service to order.
Each FoamFit insert is designed for shadowing a specific brand and set of tools. These organizers are made from high-quality tool foam with pockets precision-cut on our CNC routers.
The pockets are cut up to 1/2 inch deep in 3/4 inch thick tool foam, or up to 1 inch deep in 1-1/4 inch thick tool foam. Most inserts require less than 2 inches of height to fit in a 2-inch drawer (unless otherwise noted).
Our tool foam is two layers of closed-cell polyethylene foam. The contrasting top layer is thermally bonded to the bottom layer for maximum durability. The foam is resistant to most oils and fuels.