Drawing and Part Number Lookup |
Contact Us
920-569-0140
32 Tekton Hammer, Punch, and Pry Bar
KIT #183
Kits include both the tools and foam organizer.
This organizer is also available without tools: F-05507-T
Kit Description
32 Tekton Hammer, Punch, and Pry Bar Kit #183
This complete kit includes organizer insert F-05507-T , 7 Tekton hammers, 22 punches, and 3 pry bars.
The tool organizer may be trimmed to fit a variety of drawer sizes. Please compare the minimum recommended size to your drawer size before ordering.
Detailed drawing: F-05507-T.pdf
Tool organizer made in USA. Tools made in USA.
1-Drawer Kit
Drawer Size
38 X 18 inches
$679.60 sale $644.00
Tools Included with Kit
This kit includes the following 32 Tekton tools:
from 20-pc set PNC99001:
1/4 center punch (Tekton 66081)
3/8 center punch (Tekton 66083)
1/16 solid punch (Tekton 66071)
1/8 solid punch (Tekton 66073)
3/16 solid punch (Tekton 66075)
1/4 solid punch (Tekton 66077)
1/16 pin punch (Tekton 66051)
3/32 pin punch (Tekton 66052)
1/8 pin punch (Tekton 66053)
5/32 pin punch (Tekton 66054)
3/16 pin punch (Tekton 66055)
7/32 pin punch (Tekton 66056)
1/4 pin punch (Tekton 66057)
5/16 pin punch (Tekton 66058)
3/8 pin punch (Tekton 66059)
1/4 cold chisel (Tekton 66001)
3/8 cold chisel (Tekton 66003)
1/2 cold chisel (Tekton 66005)
3/4 cold chisel (Tekton 66007)
1 cold chisel (Tekton 66009)
1/2 center punch (Tekton 66085)
3/16 alignment punch (Tekton 66175)
from 3-pc set HDB93001:
13 oz dead blow hammer (Tekton HDB30013)
21 oz dead blow hammer (Tekton HDB30021)
39 oz dead blow hammer (Tekton HDB30039)
from 3-pc set HDB95002:
36 oz ball pein hammer (Tekton HDB50036)
43 oz short ball pein hammer (Tekton HDB51043)
50 oz long ball pein hammer (Tekton HDB50050)
26 oz flat steel face hammer (Tekton HDB40026)
from 3-pc set LSQ42103:
12-inch pry bar (Tekton 42012)
17-inch pry bar (Tekton 42017)
25-inch pry bar (Tekton 42025)
Free shipping on all orders within the contiguous 48 US states.
Drawer Requirements
The foam insert included with this kit measures 38 X 18 inches.
It is not possible to compress the foam because the tool pockets will also squeeze closed. The foam sheet can be trimmed with a sharp knife if necessary. Contact customer service if you'd like us to modify the sheet size to your measurements.
The minimum recommended size for trimming is 36-1/8 X 15-7/8 inches. This leaves a margin of approximately 1/4-inch. Trimmed organizers are not returnable.
Designer Notes
"This kit was designed to be our largest and most complete Tekton hammer kit. The hamers all have shot-filled heads for low rebound, and we've inlcuded one short and one long hammer. We added a larger center punch and an alignment punch to the Tekton 20-pc punch set which has a good selection of pin punches. This kit requires a large drawer, so measure your toolbox before ordering."
How Kits are Packaged and Shipped
After test fitting each kit, we remove the tools and seal them in a heavy-duty bag for shipping. We include a drawing to help place each tool back in the foam.
back to kits with hammers
back to kits with tools main page
view the full selection of foam tool organizers
