Contact Us |
Drawing and Part Number Lookup
920-569-0140
Foam Tool Organizer for
28 Snap-on Combination Wrenches
Overview
28 Snap-on Combination Wrenches
Fits (13) full-polish wrenches from 5/16 to 1 inch, and (15) full-polish wrenches from 8 to 22 mm.
Fits wrenches with the standard handle length.
Drawer Size
34-3/4 X 17-1/2 inches
$89.70
Details
- Drawer size: 34-3/4 X 17-1/2 inches (inside width by inside depth)
- Standard colors: black/red, blue/yellow, black/blue
- Made from closed-cell polyethylene tool foam.
- Precision CNC-cut to fit 28 Snap-on wrenches:
inch combination wrench sizes:
5/16 (Snap-on OEX10B)
11/32 (Snap-on OEX11B)
3/8 (Snap-on OEX12B)
7/16 (Snap-on OEX14B)
1/2 (Snap-on OEX16B)
9/16 (Snap-on OEX18B)
5/8 (Snap-on OEX20B)
11/16 (Snap-on OEX22B)
3/4 (Snap-on OEX24B)
13/16 (Snap-on OEX26B)
7/8 (Snap-on OEX28B)
15/16 (Snap-on OEX30B)
1 (Snap-on OEX32B)
metric combination wrench sizes:
8 (Snap-on OEXM80B)
9 (Snap-on OEXM90B)
10 (Snap-on OEXM100B)
11 (Snap-on OEXM110B)
12 (Snap-on OEXM120B)
13 (Snap-on OEXM130B)
14 (Snap-on OEXM140B)
15 (Snap-on OEXM150B)
16 (Snap-on OEXM160B)
17 (Snap-on OEXM170B)
18 (Snap-on OEXM180B)
19 (Snap-on OEXM190B)
20 (Snap-on OEXM200B)
21 (Snap-on OEXM210B)
22 (Snap-on OEXM220B)
Free shipping on all orders within the contiguous 48 US states.
Made in the USA!
note: tools are not included
Tool Requirements
This tool organizer was designed to fit full-polish, standard length Snap-on wrenches.
Possible Modifications
Minimum trimmable size:
34-1/2 X 15-1/2 inches
Note: Trimmed organizers are not returnable.
Contact customer service to order this organizer cut on a larger sheet or trimmed to a special size.
Colors by special request:
black/yellow, black/green, black/gray
contact customer service to order this organizer in a special color.
Drawing
Please verify this organizer fits your tools before placing an order.
- Download the drawing: www.FoamFitTools.com/product/F1A-01480.pdf
- Print the pages of the drawing full size or 100% (not fit).
- Check that the printout is full size by measuring the border with a ruler.
- Assemble the pages and place the printed drawing in your toolbox drawer.
- Place the tools over the printed outlines. Visually check that each tool fits within its outline.
Additional Information
Each FoamFit insert is designed for shadowing a specific set of tools. These organizers are made from high-quality tool foam with precision-cut pockets.
The pockets are cut up to 1/2 inch deep in 3/4 inch thick tool foam, or up to 1 inch deep in 1-1/4 inch thick tool foam. Most inserts require less than 2 inches of height to fit in a 2-inch drawer (unless otherwise noted).
Our tool foam is two layers of closed-cell polyethylene foam. The contrasting top layer is thermally bonded to the bottom layer for maximum durability. Three color combinations are available: black with red, blue with yellow, and black with blue. The foam is resistant to most oils and fuels.
