FoamFit Tools section divider

Foam Tool Organizer for
23 Craftsman Non-Reversible Ratcheting Wrenches, Fits Version 2

see all organizers for Craftsman ratcheting wrenches


23 Craftsman Non-Reversible Ratcheting Wrenches, Fits Version 2

Fits (12) inch and (11) metric non-reversible ratcheting wrenches.

Accommodates the wrenches from version 2 of the 298-piece set. This version of the set is made in Taiwan.

Caution: Wrenches have diagonal markings, do not have reversing levers, and are shorter than version 1.

Drawer Size
22-1/4 X 16-1/4 inches


FoamFit Tools section divider


inch sizes:
1/4 (Craftsman 39240)
5/16 (Craftsman 42568)
11/32 (Craftsman 47613)
3/8 (Craftsman 42561)
7/16 (Craftsman 42562)
1/2 (Craftsman 42563)
9/16 (Craftsman 42564)
5/8 (Craftsman 42565)
11/16 (Craftsman 42566)
3/4 (Craftsman 42567)
7/8 (Craftsman 38960)
15/16 (Craftsman 38961)

metric sizes:
6mm (Craftsman 39230)
8mm (Craftsman 42560)
10mm (Craftsman 42569)
12mm (Craftsman 42570)
13mm (Craftsman 42571)
14mm (Craftsman 42572)
15mm (Craftsman 42573)
16mm (Craftsman 39238)
17mm (Craftsman 42575)
18mm (Craftsman 42576)
19mm (Craftsman 39239)

free shipping within the contiguous 48 US states

Free shipping on all orders within the contiguous 48 US states.

Made in the USA!

Foam Organizer for 23 Craftsman Non-Reversible Ratcheting Wrenches

note: tools are not included

Tool Requirements

This organizer only fits full-polish, non-reversible ratcheting wrenches with diagonal markings. Designed to fit the wrenches from version 2 of set CMMT12039. These wrenches are made in Taiwain and are shorter than the version made in China.

Possible Modifications

Minimum trimmable size:

20-3/4 X 14-1/2 inches

Note: Trimmed organizers are not returnable.

Contact customer service to order this organizer cut on a larger sheet or trimmed to a special size.

Colors by special request:

black/yellow, black/green, black/gray

contact customer service to order this organizer in a special color.


Please verify this organizer fits your tools before placing an order.

  1. Download the drawing:
  2. Print the pages of the drawing full size or 100% (not fit).
  3. Check that the printout is full size by measuring the border with a ruler.
  4. Assemble the pages and place the printed drawing in your toolbox drawer.
  5. Place the tools over the printed outlines. Visually check that each tool fits within its outline.

Additional Information

Each FoamFit insert is designed for shadowing a specific set of tools. These organizers are made from high-quality tool foam with precision-cut pockets.

The pockets are cut up to 1/2 inch deep in 3/4 inch thick tool foam, or up to 1 inch deep in 1-1/4 inch thick tool foam. Most inserts require less than 2 inches of height to fit in a 2-inch drawer (unless otherwise noted).

Our tool foam is two layers of closed-cell polyethylene foam. The contrasting top layer is thermally bonded to the bottom layer for maximum durability. Three color combinations are available: black with red, blue with yellow, and black with blue. The foam is resistant to most oils and fuels.

Black and Red, Blue and Yellow, and Black and Blue Tool Foam
FoamFit Tools section divider

FoamFit Tools Facebook Site FoamFit Tools YouTube Channel FoamFit Tools Pinterest Site