FoamFit Tools section divider

Foam Tool Organizer for
94 Husky Impact Sockets and 9 Drive Tools

see all organizers for Husky tools

Overview

94 Husky Impact Sockets and 9 Drive Tools

Fits (94) Husky impact sockets and (9) drive tools.

Accommodates the impact sockets and drive tools from the Husky 1025-pc set H1025MTS.

Caution: Recommended for minimum of 3-1/2 inches of dawer height.

Drawer Size
13-5/8 X 19-1/8 inches

$55.20



FoamFit Tools section divider

Details

sockets:
(9) 3/8-drive 6-point inch sizes from 1/4 to 3/4
(9) 3/8-drive 6-point inch deep sizes from 1/4 to 3/4
(9) 3/8-drive 6-point metric sizes from 10 to 15 and 17 to 19 mm
(9) 3/8-drive 6-point metric deep sizes from 10 to 15 and 17 to 19 mm
(11) 1/2-drive 6-point inch sizes from 7/16 to 1-1/16
(11) 1/2-drive 6-point inch deep sizes from 7/16 to 1-1/16
(7) 1/2-drive hex bit sizes from 1/4 to 3/4
(11) 1/2-drive 6-point metric sizes from 13 to 19 and 21, 22, 24, 27 mm
(11) 1/2-drive 6-point metric deep sizes from 13 to 19 and 21, 22, 24, 27 mm
(7) 1/2-drive hex bit sizes from 9 to 15 mm

drive tools:
3/8 X 3 extension (H2DIMPEXT3)
3/8 X 6 extension (H2DIMPEXT6)
3/8-drive swivel
3/8 to 1/2-drive adapter (HIMPADP3DF2DM)
1/2 X 3 extension
1/2 X 6 extension
1/2 X 10 extension
1/2-drive swivel (H2DIMPUNIV)
1/2 to 3/8-drive adapter (HIMPADP2DF3DM)

free shipping within the contiguous 48 US states

Free shipping on all orders within the contiguous 48 US states.



Made in the USA!

Foam Organizer for 94 Husky Impact Sockets and 9 Drive Tools

note: tools are not included

Tool Requirements

This organizer was designed to fit the impact sockets and drive tools from the Husky 1025-pc set H1025MTS.

Possible Modifications

Minimum trimmable size:

13-3/16 X 18-15/16 inches

Note: Trimmed organizers are not returnable.

Contact customer service to order this organizer cut on a larger sheet or trimmed to a special size.

Colors by special request:

black/yellow, black/green, black/gray

Contact customer service to order this organizer in a special color.

Drawing

Please verify this organizer fits your tools before placing an order.

  1. Download the drawing: www.FoamFitTools.com/product/F-03428-T.pdf
  2. Print the pages of the drawing full size or 100% (not fit).
  3. Check that the printout is full size by measuring the border with a ruler.
  4. Assemble the pages and place the printed drawing in your toolbox drawer.
  5. Place the tools over the printed outlines. Visually check that each tool fits within its outline.

Additional Information

Each FoamFit insert is designed for shadowing a specific set of tools. These organizers are made from high-quality tool foam with precision-cut pockets.

The pockets are cut up to 1/2 inch deep in 3/4 inch thick tool foam, or up to 1 inch deep in 1-1/4 inch thick tool foam. Most inserts require less than 2 inches of height to fit in a 2-inch drawer (unless otherwise noted).

Our tool foam is two layers of closed-cell polyethylene foam. The contrasting top layer is thermally bonded to the bottom layer for maximum durability. Three color combinations are available: black with red, blue with yellow, and black with blue. The foam is resistant to most oils and fuels.

Black and Red, Blue and Yellow, and Black and Blue Tool Foam
FoamFit Tools section divider

FoamFit Tools Facebook Site FoamFit Tools YouTube Channel FoamFit Tools Pinterest Site