Fits the high-torque screwdrivers from the 12-pc set DRV41240 and 6-pc torx set DHT91006. Also fits screwdrivers with chrome blades.
Fits (6) slotted, (6) phillips, and (6) torx screwdrivers.
Only fits Tekton high-torque screwdrivers. Does not fit the red, hard-handle screwdrivers.
23-3/4 X 17-3/4 inches
note: tools are not included
Precision CNC-cut to fit 18 Tekton screwdrivers:
1/4 X 1-1/2 (Tekton 26621, DHE10250, or DHS30250)
1/8 X 4 (Tekton 26603 or DHS31125)
3/16 X 4 (Tekton 26613 or DHS31188)
1/4 X 4 (Tekton 26623 or DHS31250)
3/16 X 8 (Tekton 26615 or DHS34188)
1/4 X 8 (Tekton 26625 or DHS34250)
#2 X 1-1/2 (Tekton 26671, DHP10102, or DHP30002)
#0 X 4 (Tekton 26653 or DHP31000)
#1 X 4 (Tekton 26663 or DHP31001)
#2 X 4 (Tekton 26673 or DHP31002)
#1 X 8 (Tekton 26665 or DHP34001)
#2 X 8 (Tekton 26675 or DHP34002)
T10 X 4 (Tekton 26801 or DHT31100)
T15 X 4 (Tekton 26802 or DHT31150)
T20 X 4 (Tekton 26803 or DHT31200)
T25 X 4 (Tekton 26804 or DHT31250)
T27 X 4 (Tekton 26805 or DHT31270)
T30 X 4 (Tekton 26806 or DHT31300)
This organizer was originally designed to fit the 12 Tekton High-Torque screwdrivers from set DRV41216 plus the 6 torx screwdrivers from set DHT91006. It also fits the newer 12-pc set DRV41240, chrome sets DRV43007 and DHT43001, or mixed set DRV45004. It does not fit Tekton's hard handle screwdrivers which have smaller red handles.
Printing the drawing at 100% scale can be an easy way to check if your tools will fit. Our drawings have multiple pages which can be printed on letter-size paper. Always change the printer setting from "fit" to 100%. If the border prints slightly too small, it is often due to this setting.
23-3/4 X 17-3/4 inches (inside width by inside depth)
Works in most drawers, needing no more than 2 inches of vertical clearance.
It is possible to trim the margins to fit a smaller drawer. Trimmed tool organizers are not returnable. The minimum recommended size is:
21-5/8 X 14 inches
Contact customer service to order this organizer cut on a larger sheet or trimmed to a special size.
Each FoamFit insert is designed for shadowing a specific brand and set of tools. These organizers are made from high-quality tool foam with pockets precision-cut on our CNC routers.
The pockets are cut up to 1/2 inch deep in 3/4 inch thick tool foam, or up to 1 inch deep in 1-1/4 inch thick tool foam. Most inserts require less than 2 inches of height to fit in a 2-inch drawer (unless otherwise noted).
Our tool foam is two layers of closed-cell polyethylene foam. The contrasting top layer is thermally bonded to the bottom layer for maximum durability. The foam is resistant to most oils and fuels.
For orders within the contiguous 48 US states.
Made in the USA!