Foam Tool Organizer for
20 Tekton Punches and Chisels


20 Tekton Punches and Chisels

Fits the 20-pc punch and chisel set PNC99001.

Fits (2) center punches, (4) solid punches, (9) pin punches, and (3) cold chisels.


Drawer Size
11-7/8 X 17-3/4 inches


Foam Organizer for 20 Tekton Punches and Chisels

larger image

Foam Organizer for 20 Tekton Punches and Chisels

larger image

note: tools are not included

Tool List

Precision CNC-cut to fit 20 Tekton tools:

1/4 center punch (Tekton 66081)
3/8 center punch (Tekton 66083)

1/16 solid punch (Tekton 66071)
1/8 solid punch (Tekton 66073)
3/16 solid punch (Tekton 66075)
1/4 solid punch (Tekton 66077)

1/16 pin punch (Tekton 66051)
3/32 pin punch (Tekton 66052)
1/8 pin punch (Tekton 66053)
5/32 pin punch (Tekton 66054)
3/16 pin punch (Tekton 66055)
7/32 pin punch (Tekton 66056)
1/4 pin punch (Tekton 66057)
5/16 pin punch (Tekton 66058)
3/8 pin punch (Tekton 66059)

1/4 cold chisel (Tekton 66001)
3/8 cold chisel (Tekton 66003)
1/2 cold chisel (Tekton 66005)
3/4 cold chisel (Tekton 66007)
1 cold chisel (Tekton 66009)

Tool Notes

This tool organizer was designed to fit the 20-pc punch and chisel PNC99001. Model PNC99101 also will fit. The foam can be trimmed to fit a variety of drawer sizes, and we've left a bit of margin for trimming.


Drawing F-05509-R.pdf

Printing the drawing at 100% scale can be an easy way to check if your tools will fit. Our drawings have multiple pages which can be printed on letter-size paper. Always change the printer setting from "fit" to 100%. If the border prints slightly too small, it is often due to this setting.

Drawer Size

11-7/8 X 17-3/4 inches (inside width by inside depth)

Drawer Height

Works in most drawers, needing no more than 2 inches of vertical clearance.

Minimum Trimmable Size

It is possible to trim the margins to fit a smaller drawer. Trimmed tool organizers are not returnable. The minimum recommended size is:

10-1/8 X 15-7/8 inches

Contact customer service to order this organizer cut on a larger sheet or trimmed to a special size.

Features and Benefits

Standard Colors

black over red color combination blue over yellow color combination black over blue color combination

Special Colors

We make these colors in smaller batches, but they are often in stock. Contact customer service to order.

black over yellow color combination black over green color combination black over gray color combination

Additional Information

Each FoamFit insert is designed for shadowing a specific brand and set of tools. These organizers are made from high-quality tool foam with pockets precision-cut on our CNC routers.

The pockets are cut up to 1/2 inch deep in 3/4 inch thick tool foam, or up to 1 inch deep in 1-1/4 inch thick tool foam. Most inserts require less than 2 inches of height to fit in a 2-inch drawer (unless otherwise noted).

Our tool foam is two layers of closed-cell polyethylene foam. The contrasting top layer is thermally bonded to the bottom layer for maximum durability. The foam is resistant to most oils and fuels.

Free Shipping!

For orders within the contiguous 48 US states.

US flag

Made in the USA!