Drawing and Part Number Lookup |
Contact Us
920-569-0140
5 Nupla Hammer
KIT #190
Kits include both the tools and foam organizer.
This organizer is also available without tools: F-05384-R
Kit Description
5 Nupla Hammer Kit #190
This complete kit includes organizer insert F-05384-R, 5 Nupla Hammers, 1 Mayhew pry bar, and 9 Mayhew punches.
The tool organizer may be trimmed to fit a variety of drawer sizes. Please compare the minimum recommended size to your drawer size before ordering.
Detailed drawing: F-05384-R.pdf
Tool organizer made in USA. Tools made in USA.
1-Drawer Kit
Drawer Size
23-3/4 X 17-3/4 inches
$431.00 sale $347.50
We are temporarily out of the rip claw hammer for this kit. Please contact customer service for an alternate option substituting the curved claw hammer from kit 189.
Tools Included with Kit
This kit includes the following 15 Nupla and Mayhew tools:
12 oz ball pein (Nupla 21012)
16 oz ball pein (Nupla 21016)
16 oz quick change hammer (Nupla 09550)
1.5-inch red quick change tip (Nupla 15153)
1.5-inch green quick change tip (Nupla 15154)
20 oz rip claw hammer (Nupla 19020)
2 lb dead blow (Nupla Power Drive 10025)
12 inch pry bar, 17 inch overall (Mayhew Dominator 60144)
center punch, 3/8 X 5 inch (Mayhew #415, size 3/8)
line-up punch, 5/32 X 9 (Mayhew 22011, #466, size 5/32)
cold chisel, 1/2 X 6 (Mayhew #70, size 1/2)
pin punch, 1/8 X 4-3/4 (Mayhew #413, size 1/8)
pin punch, 5/32 X 5 (Mayhew #413, size 5/32)
pin punch, 3/16 X 5-1/4 (Mayhew #413, size 3/16)
pin punch, 7/32 X 5-1/2 (Mayhew #413, size 7/32)
pin punch, 1/4 X 5-3/4 (Mayhew #413, size 1/4)
brass drift punch, 1/2 X 7 (Mayhew 25076)
Free shipping on all orders within the contiguous 48 US states.
Drawer Requirements
The foam insert included with this kit measures 23-3/4 X 17-3/4 inches.
It is not possible to compress the foam because the tool pockets will also squeeze closed. The foam sheet can be trimmed with a sharp knife if necessary. Contact customer service if you'd like us to modify the sheet size to your measurements.
The minimum recommended size for trimming is 22 X 15 inches. This leaves a margin of approximately 1/4-inch. Trimmed organizers are not returnable.
Designer Notes
"This hammer kit is an update to our original Nupla hammer kit. It includes a rip claw hammer instead of a curved claw hammer. The rip claw hammer is larger and good for prying apart pallets and crates. We also added a small ball pein hammer, more pin punches, and a brass drift. These tools should come in handy working on cars, but would also be great for working on fixtures and machine tooling."
How Kits are Packaged and Shipped
After test fitting each kit, we remove the tools and seal them in a heavy-duty bag for shipping. We include a drawing to help place each tool back in the foam.
back to kits with hammers
back to kits with tools main page
view the full selection of foam tool organizers
